Yaskawa Sigma II Indexer Bedienungsanleitung Seite 176
- Seite / 227
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Sigma II Indexer User’s Manual Sigma II Indexer Status Display Table
9-5
Notes:
1. Status Codes are displayed via the Sigma II Indexer JUSP-NS600. (CN7-digital operator, CN6-
response to serial commands ALM and ERR or denial response to other commands).
Alarm
3
E19A A.EF
Program Checksum Alarm (Detected
only during initialization)
Example: Power loss during PGM-
STORE, results in corrupt program table.
OFF OFF Servo OFF YES
E1AA A.EF
Program Version Unmatched (Detected
only during initialization)
Index table version does not match firm-
ware version.
OFF OFF Servo OFF YES
E1BA A.EF
Program “Out of Range” Alarm
(Detected only during initialization)
Value set in program table is out of range.
OFF OFF Servo OFF YES
E1CA A. EF
ZONE Table Checksum Alarm (Detected
only during initialization)
OFF OFF Servo OFF YES
E1DA A. EF
ZONE Table Version Unmatched
(Detected only during initialization)
Zone table version does not match firm-
ware version.
OFF OFF Servo OFF YES
E1EA A. EF
ZONE Table “Out of Range” Alarm
(Detected only during initialization)
Value set in zone table is out of range.
OFF OFF Servo OFF YES
E1FA A. EF
JOG Speed Table Checksum Alarm
(Detected only during initialization)
OFF OFF Servo OFF YES
E21A A. EF
JOG Speed Table Version Unmatched
(Detected only during initialization)
Jog speed table version does not match
firmware version.
OFF OFF Servo OFF YES
E22A A. EF
JOG Speed Table “Out of Range” Alarm
(Detected only during initialization)
Value set in jog speed table is out of
range.
OFF OFF Servo OFF YES
E23A A.EF
Insufficient Registration Distance Alarm
The reserved registration distance is too
small compared to the distance it takes
the motor to decelerate to the reserved
registration speed.
OFF OFF Servo OFF YES
9.2.1 Sigma II Indexer Alarm Status Display Table
Indexer
Status
Status
1
Code
Panel
2
Display
Detail
ALM
3
Output
/WARN
4
Display
Motor
Operation
Reset
5
- Safety Information 3
- Overview 8
- Using This Manual 9
- Safety Precautions 10
- 1.1 Introduction 15
- Figure 1.5 17
- Table 1.3: Part Numbers 18
- Figure 1.8 21
- Installation 22
- 2.1 Storage Conditions 23
- 2.2 Installation Site 24
- 2.3 Orientation 25
- 2.4 Installation 26
- Connectors 28
- 3.1 I/O Signals (CN1, CN4) 29
- CNIO Dual Port RAM 30
- (ON when in-position) 30
- Programmable 30
- 10250–52A2JL or 32
- Equivalent 50–pin 32
- Right Angle 32
- Receptacle 32
- RS232/422 37
- RS232/422/485 37
- P: Personal computer 40
- S: Servopack 40
- Table 3.13: 40
- 3.2.6 Connection Examples 41
- RS422/485 Interface Cable 43
- Maximum power loss 2.6 W max 44
- Item Specification 44
- Trial Operation 46
- 4.1 Two-Step Trial Operation 47
- (no-load conditions) 49
- Panel operator 50
- P-OT CN1-42 52
- N-OT CN1-43 52
- /S-ON CN1-40 52
- +24VIN CN1-47 52
- Display with the servo ON 53
- Servomotor 54
- Connect to the machine 54
- Before Reading this Chapter 58
- Parameter Configurations 58
- Parameter Signal Setting 61
- Setting Description 61
- Stop Mode After stopping 66
- 5.3 Sequence I/O Signals 67
- Servo amplifier 70
- Host controller 70
- Turns power OFF 71
- ALM output 71
- Figure 5.7 Holding Brake 72
- /S-ON input 74
- /S-RDY CN1-29, 30 75
- Servo Ready Output Signal 75
- CN1-25 /WARN+ 76
- CN1-26 /WARN 76
- A 13 2048 16 to 2048 83
- 16384 16 to 16384 83
- Reference unit: 1Pm 84
- D: Pulley 85
- Ball Screws 87
- Circular Tables 87
- [0.01msec] 89
- 5.6 Absolute Encoders 90
- Battery carrying space 92
- Batter connector (CN8) 92
- Up Cursor Key 93
- Flashes for one second 93
- Flashes for 95
- 1 second 95
- Signal Status Contents 97
- 5.7.3 Program Step Selection 103
- Min. 4 ms 112
- Min. 2 ms 112
- Min. 0 ms 112
- Min. 8 ms 112
- 5.8 Registration 113
- 5.9 Zone Table Set-up 116
- 5.10 Program Table Examples 118
- (Example) 119
- Table 5.14a: Zone Table 121
- Table 15a: Zone Table 122
- Home Position, Pn 823: 125
- 5.12 Homing Routine Operation 126
- Figure 5.13 Jog Speed Table 127
- Serial Commands 130
- 6.1 Specifications (CN6) 131
- 6.2 Control Configuration 132
- 6.3.1 Command Format 134
- 6.3.2 Echo Back Response Time 135
- Table 6.4: 135
- 6.5 Serial Command Functions 137
- 6.5.2 Moving Commands 138
- Table 6.6: Moving Command 138
- Using the Digital Operator 164
- Hand-held Digital Operator 165
- JUSP-0102A-1 165
- Servo Amplifier 165
- 7.1.2 Functions 166
- Built-in Panel Operator 167
- IMPORTANT 168
- 7.1.4 Basic Mode Selection 169
- Dimensional Drawings 170
- Troubleshooting 172
- 9.4 STS Status LEDs 185
- Appendix A 186
- Table A.1: Indexer Parameters 187
- Appendix A-6 191
- Appendix A-7 192
- Appendix A-8 193
- A.3 Servo Amplifier Switches 195
- Appendix A-11 196
- Appendix A-12 197
- Appendix B 198
- B.1 Monitor Modes 199
- Table B.1: Monitor Modes 200
- B.2 Auxiliary Functions 201
- Appendix B-5 202
- Appendix B-6 203
- Appendix C 204
- Appendix C-2 205
- Appendix C-3 206
- Appendix C-4 207
- Appendix D 208
- Appendix D-2 209
- Appendix D-3 210
- Appendix D-4 211
- Appendix D-5 212
- Appendix D-6 213
- Appendix D-7 214
- Appendix D-8 215
- Appendix D-9 216
- Appendix D-10 217
- Appendix D-11 218
- Appendix D-12 219
- Appendix D-13 220
- Appendix D-14 221
- Appendix D-15 222
- Appendix D-16 223
- Appendix D-17 224
- Appendix D-18 225
- Appendix D-19 226
Verwandte Produkte und Handbücher für Ausrüstung Yaskawa Sigma II Indexer
Ausrüstung Yaskawa YTerm Bedienungsanleitung
(56 Seiten)
(56 Seiten)
Ausrüstung Yaskawa LEGEND-MC Bedienungsanleitung
(360 Seiten)
(360 Seiten)
Ausrüstung Yaskawa SMC–4000 Bedienungsanleitung
(385 Seiten)
(385 Seiten)
Ausrüstung Yaskawa MP2000iec Bedienungsanleitung
(102 Seiten)
(102 Seiten)
Ausrüstung Yaskawa MP3200iec Bedienungsanleitung
(96 Seiten)
(96 Seiten)
Ausrüstung Yaskawa Yasnac PC NC Bedienungsanleitung
(389 Seiten)
(389 Seiten)
Ausrüstung Yaskawa SGDB Bedienungsanleitung
(585 Seiten)
(585 Seiten)
Ausrüstung Yaskawa V1000 Bedienungsanleitung
(136 Seiten)
(136 Seiten)
Ausrüstung Yaskawa A1000 CIMR-AU Bedienungsanleitung
(276 Seiten)
(276 Seiten)
(60 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern