Yaskawa F7 Drive User Manual Bedienungsanleitung Seite 156
- Seite / 255
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Diagnostics & Troubleshooting 6 - 31
Drive Date Stamp Information
This information is used to determine when a Drive was built to see if it is within its warranty period. The date stamp is located
on the lower right side of the Drive.
Fig 6.1 Date Stamp Location
Table 6.6 Main Circuit Test Procedure (continued)
Check Procedure
24Vdc Cooling Fans
(Heat Sink & Internal)
The Heat Sink & Internal Cooling Fans cool the heat sink as well as the output transistor
modules of the Drive.
1. Conduct a visual inspection to ensure the fan turns freely.
2. If there is no physical evidence that the fan is bad, the fan motor can be checked with a
digital multi-meter.
3. Set the digital multi-meter to the R x 1 scale.
4. Measure across the fan motor terminals. If 0
Ω are measured, conclude that the fan motor is
shorted. If infinite
Ω are measured, conclude that the fan motor is burned open.
5. If the fan is not working, then disconnect the fan and apply 24Vdc to the fan to test the motor.
230/240Vac Cooling Fans
(Heat Sink)
The Heat Sink Cooling Fans cool the heat sink to remove heat from the Drive.
1. Conduct a visual inspection to ensure the fan turns freely.
2. If there is no physical evidence that the fan is bad, the motor can be checked with a digital
multi-meter.
3. Set a digital multi-meter to the R x 1 scale.
4. Measure across the fan motor terminals. If the fan motor is good, the measured value should
be about 500
Ω. If 0Ω are measured, conclude that the fan motor is shorted. If infinite ohms are
measured, conclude that the fan motor is burned open.
5. If the fan is not working, then disconnect the fan and apply 230/240Vac to the fan to test the
motor.
Cooling Fan Fuse
Large Drive units contain a Cooling Fan Fuse. It is located on either the Gate Drive Board (3PCB)
or the Tap Change Board (8PCB). If the Cooling Fan Fuse is open, then the 230/240Vac cooling
fans may be defective.
1. Set a digital multi-meter to the R x 1 scale.
2. Place one lead of the multi-meter on one side of the fuse and place the other lead of the multi-
meter on the other side of the fuse.
3. If the fuse is good, the measured value will be 0
Ω. If the fuse is bad, the measured value will
be infinite
Ω.
PRD
INSP2
96 3. 31
YEA Production
Manufacture Date
Inspector Number
00.7.22
- F7 Drive 1
- User Manual 1
- Warnings and Cautions 2
- Intended Use 3
- Introduction 4
- Drive Output Specifications 5
- Table of Contents 8
- Chapter 1 12
- Physical Installation 12
- Physical Installation 1 - 2 13
- Confirmations upon Delivery 14
- Drive Model Numbers 15
- Component Names 16
- Physical Installation 1 - 6 17
- Physical Installation 1 - 7 18
- Physical Installation 1 - 8 19
- Physical Installation 1 - 9 20
- Physical Installation 1 - 10 21
- Installation Site 22
- Physical Installation 1 - 12 23
- Removing the Terminal Cover 24
- Physical Installation 1 - 14 25
- Physical Installation 1 - 15 26
- Physical Installation 1 - 16 27
- Chapter 2 28
- Electrical Installation 28
- Terminal Block Configuration 29
- Wiring Main Circuit Terminals 30
- Wire Size * 35
- Terminal Screw 35
- Ground Wiring 38
- Dynamic Braking Connections 39
- SP and S3 is programmed as 43
- External Fault 43
- Terminal Connections 46
- Control Wiring 47
- DIP Switch S1 and Jumper CN15 49
- Sinking/Sourcing Mode 50
- Control Circuit Wire Sizes 51
- Wiring Checks 51
- Field Wiring Diagram 52
- Introduction 53
- Cable Installation 53
- Fig 2.15 EMC Filter Layout 54
- Motor Cable 54
- Max. Length: 82 feet 54
- Recommended EMC Filters 55
- Installation 58
- Circuit 59
- Protection 59
- Wiring the PG-B2 61
- Wiring the PG-D2 63
- Drive 66
- Wiring Terminal Blocks 67
- PG-A2/PG-B2 68
- PG-D2/PG-X2/PG-W2 69
- Chapter 3 70
- Digital Operator 70
- Digital Operator Display 71
- Digital Operator Keys 72
- Drive Mode Indicators 73
- Run Indicator 74
- Stop Indicator 74
- Drive Main Menus 75
- Main Menu Structure 76
- Operation Menu (-DRIVE-) 77
- Digital Operator 3 - 9 78
- Digital Operator 3 - 10 79
- Quick Setting Menu (-QUICK-) 80
- Programming Menu (-ADV-) 81
- Auto-Tuning Menu (-A.TUNE-) 82
- Digital Operator 3 - 14 83
- Digital Operator 3 - 15 84
- Digital Operator 3 - 16 85
- Chapter 4 86
- Start-Up 86
- Drive Start-Up Preparation 87
- Start-Up 4 - 3 88
- Start-Up 4 - 4 89
- Drive Start-Up Procedures 90
- V/F Start-Up 91
- V/F w/ PG Start-Up 92
- Open Loop Vector Start-Up 93
- Flux Vector Start-Up 94
- Auto-Tuning 95
- Start-Up 4 - 11 96
- Quick Setting Parameters 97
- Start-Up 4 - 13 98
- Start-Up 4 - 14 99
- Trial Run 100
- Start-Up 4 - 16 101
- Chapter 5 102
- Basic Programming 102
- Control Method 103
- Speed Command Source 104
- Run Command Source 105
- Stopping Method 106
- Basic Programming 5 - 6 107
- Basic Programming 5 - 7 108
- Output Frequency 109
- Carrier Frequency 110
- Basic Programming 5 - 10 111
- Preset Reference 112
- Input Voltage Setting 113
- V/F Pattern 113
- Basic Programming 5 - 13 114
- E1-09 E1-07 116
- Basic Programming 5 - 16 117
- Basic Programming 5 - 17 118
- Basic Programming 5 - 18 119
- Basic Programming 5 - 19 120
- Motor Setup 121
- PG Option 121
- Output Function Level (%) 122
- 10V x 150% 122
- 0Disabled 123
- default) 123
- 3 Vector Motor ( 123
- Stall Prevention 124
- Basic Programming 5 - 24 125
- Chapter 6 126
- Fault Detection 127
- <3021> 129
- Alarm Detection 135
- Auto-Tuning Faults 142
- Troubleshooting 145
- Vector Control Method 147
- If Motor Deceleration is Slow 148
- If the Motor Overheats 149
- Check Procedure 153
- Fig 6.1 Date Stamp Location 156
- Chapter 7 158
- Maintenance 158
- Periodic Inspection 159
- Preventive Maintenance 160
- Periodic Maintenance of Parts 161
- Maintenance 7 - 5 162
- Connector 162
- Maintenance 7 - 6 163
- Maintenance 7 - 7 164
- Maintenance 7 - 8 165
- Appendix A 166
- Parameters 166
- Parameters A - 2 167
- F7 Parameter List 168
- Parameters A - 4 169
- Parameters A - 5 170
- Parameters A - 6 171
- Parameters A - 7 172
- Parameters A - 8 173
- Parameters A - 9 174
- Parameters A - 10 175
- Parameters A - 11 176
- Parameters A - 12 177
- Parameters A - 13 178
- Parameters A - 14 179
- Parameters A - 15 180
- Parameters A - 16 181
- Parameters A - 17 182
- Parameters A - 18 183
- Parameters A - 19 184
- Parameters A - 20 185
- Parameters A - 21 186
- Parameters A - 22 187
- Parameters A - 23 188
- Parameters A - 24 189
- Parameters A - 25 190
- Parameters A - 26 191
- Parameters A - 27 192
- Parameters A - 28 193
- Parameters A - 29 194
- Parameters A - 30 195
- Parameters A - 31 196
- Parameters A - 32 197
- Parameters A - 33 198
- Parameters A - 34 199
- Parameters A - 35 200
- Parameters A - 36 201
- Parameters A - 37 202
- F7 Monitor List 203
- 0 0 0 0 0 0 0 0 204
- F7 Fault Trace List 206
- F7 Fault History List 206
- Parameters A - 42 207
- Appendix B 208
- Capacity Related Parameters 208
- Drive Capacity Selection 209
- Appendix C 214
- Specifications 214
- Standard Drive Specifications 215
- 480Vac 216
- Common Specifications 217
- Specifications C - 5 218
- Specifications C - 6 219
- Appendix D 220
- Communications 220
- Using Modbus Communication 221
- Communications D - 3 222
- Communications D - 4 223
- 08H Loopback Test 8 8 8 8 224
- Communications D - 6 225
- Communications D - 7 226
- Modbus Function Code Details 227
- Loopback Test (08H) 228
- Modbus Data Tables 229
- Communications D - 11 230
- Communications D - 12 231
- Communications D - 13 232
- Communications D - 14 233
- Communications D - 15 234
- Communications D - 16 235
- Communications D - 17 236
- Modbus Self-Diagnosis 237
- Appendix E 238
- Peripheral Devices 238
- Peripheral Devices E - 2 239
- Peripheral Devices E - 3 240
- Peripheral Devices E - 4 241
- Peripheral Devices E - 5 242
- Appendix F 244
- Spare Parts 244
Verwandte Produkte und Handbücher für Ausrüstung Yaskawa F7 Drive User Manual
Ausrüstung Yaskawa F7 Modbus Bedienungsanleitung
(84 Seiten)
(84 Seiten)
Ausrüstung Yaskawa G5HHP Drive Bedienungsanleitung
(374 Seiten)
(374 Seiten)
Ausrüstung Yaskawa MP940 Bedienungsanleitung
(522 Seiten)
(522 Seiten)
Ausrüstung Yaskawa CIMR-LE Bedienungsanleitung
(520 Seiten)
(520 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.627 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern